Description of data per node?
Hi, I'm new to the things network and have a small question. When I make an api-call to http://thethingsnetwork.org/api/v0/nodes/ I get a list of nodes. I can furthermore make api calls to extract the...
View ArticleDescription of data per node?
no, it's completely up to the user/developer of the node to decide what data his/her node sends. so everyone just sends whatever he wants, as long as the packets don't get too long. (because it's an...
View ArticleMeasuring coverage gateway
Hi all, short question.What's the best way to measure the coverage of a gateway? Cheers, Dagmar
View ArticleClik here to view.
Measuring coverage gateway
@kersing I suppose you mean hardware? I'm using both a LoRaMote, and ... ahem ... this contraption: That's a Sodaq autonomo with GPS module, battery, RN2483, small screen (not necessary, but it shows...
View ArticleClik here to view.
Measuring coverage gateway
@Kersing Thx, good advice !. I must admit that I'm adapting the duty cycle to get more samples / hour In my/our defense: In that way we are not exceeding the duty-cycle at any location as long as we...
View ArticleLinks Lab LL-BST-8
Symphony is a completely different MAC for LoRa. It is created for private network applications in 900 MHz, where duty cycle is not limited....
View ArticleClik here to view.
Description of data per node?
Batilan: I think @pz1 is after something similar Yes I am. I hope many will contribute to the collection of reference nodes
View ArticleClik here to view.
Kerlink setup
The LoRaMote by IMST works out of the box. The data collected has to be processed and I wrote a little python script. It's a bit ugly but good for inspiration, and more people on the forum made...
View ArticleHardware installation of kerlink
how to set up the kerlink gateway?? i mean the hardware setup
View ArticleKerlink gateway booting
The gateway is supplied and communicates through a standard 10/100T Ethernet cable. The PoE power injector is supplied with the gateway. The antenna must be connected through a low loss N type coaxial...
View ArticleClik here to view.
Measuring coverage gateway
I have yet to recharge it it's not on contuinously, so I don't know.
View ArticleKerlink gateway booting
normally all leds are off. press the TEST button, this will light up the leds for about a minute or so.
View ArticleClik here to view.
Measuring coverage gateway
Batilan: Currently I'm using the format: counter,lat,lon Using the counter allows to see when transmissions are lost. The LoRaWAN packet already has an (unencrypted) counter, no need to add it in the...
View ArticleClik here to view.
Measuring coverage gateway
I don't understand why coverage measurements should be done at SF12 as a "normal" node sends at SF7? so we would then artificially extend the coverage... at SF12/ 125khz / CR4/5 sending just a 16 bit...
View ArticleClik here to view.
Measuring coverage gateway
anyway this is my location payload .. i used (other than the official loramote) a 32 instead of a 24 bit location, because I think 24 bit is not accure enough, especially for the longitude. this...
View ArticleCollection of Permanent Reference NODES
Well, here a few formats that I just harvested with Node-RED: 02011B01 {temp0:20.00,humi0:17.00}02020401 Hello Things4U02030603 { "temperature":18.6}02015801 Hello, world!02012A02...
View ArticleClik here to view.
Measuring coverage gateway
niels: I don't understand why coverage measurements should be done at SF12 as a "normal" node sends at SF7? so we would then artificially extend the coverage... at SF12/ 125khz / CR4/5 sending just a...
View ArticleMeasuring coverage gateway
ADR etc only works (a.f.a.i.k.) with a CONFIRMED SEND, which costs much (like at least triple) more airtime and is not the preferred default way to send your packets in my opinion? and a node default...
View Article