Messages are out of order and/or missing in the API
Hi I can be the firmware. But also if you require an ACK from TTN. You should change the follwing line;uint8_t CMD_SEND_PREFIX[4] = { 0x50, 0x0C, 0x00, PORT }; // 0x50 0x08 0x00 PORT for without 0x0C...
View ArticleClik here to view.
Wiki.thethingnetwork.org not working
I think its because of overload of requests on the API... Maybe we have to set a limit for requesting. Like 5 minutes to capture your node's?
View ArticleWiki.thethingnetwork.org not working
the MQTT service is also down (i'm actively using/testing it) tcp://croft.thethings.girovito.nl:1883 :-(((((((((
View ArticleClik here to view.
Wiki.thethingnetwork.org not working
niels: tcp://croft.thethings.girovito.nl:1883 My application logged this as first time of failure:22.12. - 13:02 | Can not fetch TTN node information
View ArticleWiki.thethingnetwork.org not working
504 Gateway Time-out nginx/1.6.2 (Ubuntu) on http://www.thethingsnetwork.org
View ArticleClik here to view.
RN2483 Breakout?
Another alternative that is simpler and only uses the antenna connection for the 868MHz. It doesnt bother with the GPIO connections as there, I see these having very limited use when the module is...
View ArticleMicrochip RN2483 use
Would be nice if we could reprogram the PIC18F46K22 inside the module, perhaps with the IBM code, for a self contained unit.Or is the sourcecode for the PIC chip available somewhere? That would make a...
View ArticleClik here to view.
RN2483 Breakout?
Andrew's breakout PCB is working great for me, was no problem to drag solder the module onto and the red colour is a winner Cheers! - Jose
View ArticleClik here to view.
Wiki.thethingnetwork.org not working
Guess its down for the holidays...pack up and go home, do something nice with our families
View ArticleMicrochip RN2483 use
I think for the LoRaAlliance certification, the PIC micro within the RN2483 will not be able to run user code. This is a similar situation with the MultiTech mDot modules where the micro can actually...
View ArticleSingle Channel Gateway
Hi Vidal, Yes, that should work. You probably want to set the single channel center to 915.1 Mhz then (it is 125 kHz wide). Thomas
View ArticleClik here to view.
REST API: get your node data
Website is up again. The problem was indeed Croft (and the database) being down with connections timing out after 30sec only. I've set it to 3sec, and returning a nice error message to the API caller....
View ArticleClik here to view.
Wiki.thethingnetwork.org not working
See REST API: get your node data Website is up again. The problem was indeed Croft (and the database) being down with connections timing out after 30sec only. I've set it to 3sec, and returning a nice...
View ArticleSetting up your first gateway
Hi,I got the same problem while connecting the Multitech mCard to a Raspberry Pi 2 Model B using exactly the same instructions from @nestorayuso. Because I used the mCard earlier on another server...
View ArticleLeiden, The Netherlands
So, finally got round to getting my node up and running on TTN, only to find that API is now broken. Anybody know where to flag this? http://thethingsnetwork.org/api/v0/gateways/0203090000000001/ HTTP...
View ArticleLeiden, The Netherlands
@Robin did you check the latest messages on the forum? http://forum.thethingsnetwork.org/t/rest-api-get-your-node-data/102/40
View ArticleREST API: get your node data
As reported on Slack now the API is functional again (since about 19:55 UTC / 20:55 Amsterdam it seems)
View ArticleLeiden, The Netherlands
The API is up again now! At first no joy, but just hooked up a big antenna to my node; that helped! Now getting some data through from the Schelpenkade to gateway 0203090000000002. So that's about 1...
View Article