Almere, The Netherlands
Oscar,Node 02013D42 is my node, not Arjan's. It is a MicroChip Technology Mote.The default application sends the light intensity and temperature in the payload: 5 ASCII characters for light (01023...
View ArticleAlmere, The Netherlands
@okneib - do you still have issues and which Sodaq is giving issues ? The autonomo is working fine.
View ArticlePurchasing Hardware
Did you consider buying the lorank8 or building your own with an IMST board and a raspberry pi?
View ArticleClik here to view.
Is anyone already working on the PetFinder use case?
UncleJohn: Node ID is likely needed to allow tracking of multiple animals. @UncleJohn, node ids are always known when receiving LoRaWAN packets.
View ArticleClik here to view.
Is anyone already working on the PetFinder use case?
oops.. didn't read your original post correctly.. sorry.(late in the day...eyes playing tricks on me)
View ArticleSPN version of the Kerlink IoT gateway
Do you have more technical details about the software integrated on the Kerlink SPN version?I could find very little on the Internet, and Kerlink's website is also rather silent on it.I have mailed...
View ArticleClik here to view.
SPN version of the Kerlink IoT gateway
I still haven't received the gateway so I don't know if they are shipping any documentation with it.I agree that the website isn't of much help and their email communication is rather sluggish I will...
View ArticleClik here to view.
Purchasing Hardware
Hi JimK, Think I'm in the same mood ...gathering as much info about all the availblable gateways....just to make my final choice.I've contacted Libellium too for info of their Meshlin. I also had some...
View ArticlePurchasing Hardware
Hi Marco, I've just received the same response from Libellium. I didn't find that in any of the documentation at all. Which is a bit of pain given the amount of time I've spent researching this. It's...
View ArticleTTN Manifesto and Open Data
There is a group running a project sharing sensor data. https://iotic-labs.com/experience/uses/ It sounds like this proposal is similar to their aspiration of making sensor data available to all. It...
View ArticleChennai, India
Hi all, I am interested to setup the first LoRa gateway from Chennai and started the groundwork to build one in coming weeks/months. Hopefully, we will get a device from TTN kickstarter or could build...
View ArticleClik here to view.
Smallest expected node
projextX147.jpg960x691 214 KB did some more testing with diffent pir modules from China and this one I liked best.4/5 mtr wide angle detection / 30 uA @3V and after 2sec auto reset
View ArticleClik here to view.
RN2483 Breakout?
I designed a Arduino shield for the RN2483 in KiCad. Revision 2 of the board, including libraries, is available here: https://github.com/jpmeijers/RN2483shield Revision 1 works quite well. Feel free...
View ArticleClik here to view.
Purchasing Hardware
Hi Jim, The Kerlink Gateways are available here : http://www.mcs-nl.com/vmchk/LoRa/LoRa-Outdoor-BaseStation-Kerlink/flypage.tpl.html
View ArticleRN2483 Breakout?
Very good question! According to the datasheet the input pins on the RN2483 can only handle up to 4.2V (max Vcc 3.9 + 0.3). But I've been giving them 5volt for more than 3 months now, without any...
View ArticleMeasuring coverage gateway
As a response to what Ton has said here a few days ago, I link here my KML files of coverage tests in Enschede. Please note that it is hosted on a very slow VPS, so don't expect a lot of speed when...
View ArticleRN2483 Breakout?
In my experience I also found that after using them directly that they were OK, but to be on the safe side with my design I added the level shifters to the tx/rx pins. When applying 5V to the module...
View Article