Can't receive ACK from LinkLabs Gateway LoraWAN?
Hello, When I send message to Gatway LoraWan via his UHF interface ( created by LinkLabs) using other devices with UHF interface ( antenna ), there is no response . i followed all step of...
View ArticleHeerhugowaard, The Netherlands
Gateway Heerhugowaard up and running!. Eerste testpakketje verstuurd en aangekomen op de site van TheThingsNetwork.
View ArticleClik here to view.
Is the LoRa gateway hardware also Open Source, and where do I find it?
Limro: I am creating an application which allows me to locate a tag based on DTOA. To make this possible, I would like to use the GPS's PPS (Precision Pulse Signal), activate a timer, and interrupt it...
View Article's Hertogenbosch, The Netherlands
Well, that was easy. Although currently in a test setup the gateway seems to work. At least I ran through all the steps in https://github.com/ttn-zh/ic880a-gateway/wiki without errors so I guess it's...
View ArticleClik here to view.
's Hertogenbosch, The Netherlands
Don't forget the last step of @gonzalocasas' instructions! Pasted image1355x1016 1.66 MB
View ArticleClik here to view.
's Hertogenbosch, The Netherlands
I'm afraid I can't match that level of professionalism.
View Article's Hertogenbosch, The Netherlands
That should not be too hard. You just need a plastic box for outdoor use, available from a number of electronics shops, and a "pigtail".The pigtail needs to be an SMA-SMA pigtail like the one sold by...
View ArticleRepair of burnt iC880A IMST Gateway
Hi guys, I've accidentally connected wrong DC adapter to my iC880A IMST board (24V instead of 5V) and it stopped working immediately. There's no physical changes in the board and no smell but it's not...
View ArticleKerlink installation not possible (wiki possibly out-of-date)
I have a Kerlink IOT station 868 installed on the roof without physical access to it. Is there any possibility to install TTN packet forwarder over ssh?
View ArticleKerlink installation not possible (wiki possibly out-of-date)
Do you have SSH access to the device? If so, yes.
View ArticleKerlink installation not possible (wiki possibly out-of-date)
Yes I have ssh access, but not sure how to start installation.There are two scripts begin_dota.sh and end_dota.sh in dota_thethingsnetwork_SmartParcs_v1.5 folder.
View ArticleToronto & GTA
Hi Al and Darren, Firstly, it's a pleasure to "e-meet" both of you. I'm currently in Waterloo and go between Waterloo and Toronto a fair bit. A friend and I are interested in setting up gateways in...
View ArticleHeerhugowaard, The Netherlands
Hoi Ruud, Onlangs aangesloten en een Gateway besteld. Kan niet wachten tot hij binnen (juli 2016) is en hem online te brengen. Komt aan de Reuzenpandasingel dus een mooi stukje van het zuiden ook...
View ArticleHeerhugowaard, The Netherlands
Ruud, voor dekking Alkmaar / Heerhugowaard en omstreken neem even contact met mij op gerard.duineveld@alticom.nl .. thnx
View ArticleClik here to view.
[IMST IC880A + RPi] Gateway "hangs" every few weeks
The aluminum box helped quite a lot, but did not solve the problem. Uptime in the (RF-noisy) office went up from several hours to several days. For now cron restarts the ttn-gateway service (which...
View ArticleClik here to view.
[IMST IC880A + RPi] Gateway "hangs" every few weeks
melvin: Has anyone contacted IMST yet? I did send a mail to the personal mail address of one of the people I had contact with before but did not yet receive a reply. I just sent a message via the...
View ArticleKerlink installation not possible (wiki possibly out-of-date)
There is no special need for the TTN packetforwarder as far as I can see. I operate two kerlinks running the Kerlink PF.
View ArticleClik here to view.
[IMST IC880A + RPi] Gateway "hangs" every few weeks
Batilan: I wonder how it is with the Lorank8 gateways as they are based on the same board AFAIK. Anyone? The Lorank8 uses the same IMST hardware, and does not have this problem at all. The software is...
View ArticleClik here to view.
[IMST IC880A + RPi] Gateway "hangs" every few weeks
Thomas: The differences are BaegleBone vs Raspberry, and a (passive) PCB between the BeagleBone and the IMST board. Thanks Thomas. Could it be "flaky connections" due to using jumper wires instead of...
View ArticleRunning TTN back-end locally reports gateway errors
Hi @htdvisser I have tried again the downlink, and I have the impression that it might be the gateway of my devices, but I'd need your knowledge over the debug messages given by the TTN backend to...
View Article