Clik here to view.
Over-the-air-activation OTAA with LMIC
Kibet: I just discovered that messages are actually being send, only after a (yet) inexpiable long time (approximately 15 min). ernestopace: I do see very varying JOIN times, in the order of 1-3...
View ArticleClik here to view.
Over-the-air-activation OTAA with LMIC
Awesome, I've just tested it, and patience is the key Thanks a lot everyone!!
View ArticleGateway for 919 to 923 MHz
Anyone know which gateway available in market allows us to modify the LoRa frequency of 125kHz to operate at 919 to 923 MHz?
View ArticleClik here to view.
Gateway for 919 to 923 MHz
@ChunYeow Thanks for asking this in the forum. I was thinking to ask similar question too. I guess the US version gateway (915MHz) would be the one that we could modify to operate at 919 to 923 MHz....
View ArticleGateway for 919 to 923 MHz
The frequencies used by the gateways are specified in the global_conf.json configuration file, so 'modifying' a gateway is done by modifying the configuration file. TTN currently provides...
View ArticleGateway for 919 to 923 MHz
The US version gateway (915MHz) operates at 902 to 928 MHz. So, no need for modification. The two or three SAW filters used in gateways: TA1561A @ 915 Center (26 MHz Bandwidth 902-928 MHz) cover the...
View ArticleAlternative for iC880A antenna?
Is it possible to extend the length of the coax for those antenna's?
View ArticleKerlink installation not possible (wiki possibly out-of-date)
Hi Guys, and hopefully the TTN team. I have been trying to install TTN on two separate Kerlinks, which i will refer to as KA and KB. KA is running Kerlinks own "SPN" software, and KB runs ThingPark. I...
View ArticleGateway for 919 to 923 MHz
I am aware of that. Which gateway has been tested using this config file?
View ArticleGateway for 919 to 923 MHz
Yes, it would be great if the TTN gateway can do this. Anyone knows whether this is supported? By the way, once we have the gateway doing so. How about the sensors? Any suggestions?
View ArticleAustralia: Melbourne and beyond
Hi all.I would be interested in setting this up in Rockhampton, QLD. Any communication is welcomed. Kind regardsGlendon
View ArticleTTN UNO - BETA release - Documentation
I successfully upgraded my Lorabee to firmware 1.01 with the LoRaDevelopmentGUI (lora.jar). I did this connecting my lorabee directly to my FTDI pcb (or cable might also work) , connecting (UART)...
View ArticleOver-the-air-activation OTAA with LMIC
Yeah the node is 30 meters away from the gateway. With ABP it has always been an instant join, even at a distance of 1.5 km. Same goes for the RN2483 with OTAA. Thus something different happens when I...
View ArticleClik here to view.
Kerlink installation not possible (wiki possibly out-of-date)
Thanks Nicholas for sharing this information. As for the different Kerlinks, this is something new (for us) that there are different types of Kerlinks around. Even with their own wikis . We have to...
View ArticleOver-the-air-activation OTAA with LMIC
In the LoRaWAN 1.0 specification the duty cycle for joins in EU is indeed 0.1%. So if the initial joins fails for whatever reason, it will take a long time before it sends another attempt. The LoRaWAN...
View ArticleKerlink installation not possible (wiki possibly out-of-date)
Hi @fokko, thanks for looking into this! For updating the new wiki and the Kerlink page, please file a pull request for the rewrite branch.
View ArticleClik here to view.
LMIC-1.51 fitting in Arduino Atmega 328
ernestopace: Do you have any idea why OTAA might not work with the alternative AES implementations? I had a look through my code, and I think this is the culprit: case AES_ENC: // TODO: This assumes...
View Article[IMST IC880A + RPi] Gateway "hangs" every few weeks
Maybe it would be worth making some kind of script that runs sudo service restart ttn-gateway once in a while
View ArticleLMIC-1.51 fitting in Arduino Atmega 328
I have been working on a smaller EAS llb this weekend. I have a slighly different codebase, but the function should be called several times depending on the length of the buffer.: unsigned character...
View ArticleAnnouncing staging environment of TTN Back-end 1.0
That is currently not possible. For this, we need to introduce a new topic, e.g. <AppEUI>/devices/<DevEUI>/down-tx. You can submit an issue for this on GitHub.
View Article