What if...?
Remember in the UK there is no such thing as 'unlicensed' spectrum, it's all license exempt - which means that specific Acts of Parliament (Statutory Instruments) have been passed to allow use of...
View ArticleRx2 Frequency for USA
Thomas, Thank you very much for the reply. Indeed the channel configuration was the primary issue. I used "mac set ch status X off" for all channels except 48,49,50,51 which are configured in the...
View ArticleThe Things Network - Melbourne Community
Melbourne`s TTN community discussion http://thethingsnetwork.org/c/melbourne
View ArticleClik here to view.
The Things Network - Melbourne Community
If anyone wants to join our community, please join here at the forum first, so we can start the discussion about the planned tasks and ongoing activities.Thanks
View ArticleThe Things Uno SDK
Looks nice and easy this way.1. I miss the "mac get status" call. I use that allways before a transmit to check if the devices is ready.2. From the example, ttu.sendString() returns true or false ,...
View ArticleBackground page photo help
Hey @Yesway, if you could email me (community@thethingsnetwork.org) the picture, I could update the Lincoln page.
View ArticleClik here to view.
MARCONI 6960B rf power meter
6960B.jpg1200x674 188 KB anyone familiar with this instrument ? ' Houston , do we have a problem ? ' https://www.youtube.com/watch?v=rio8aR80y6A https://www.youtube.com/watch?v=HIx86JyqMpw (or is this...
View ArticleBackground page photo help
And note that things might change soon: New design community page.
View ArticleClik here to view.
Onboard/Concealed Antennas
I just ran into a nice explanation of 433 MHz and 868 MHz Antenna Design Examples. It sounds good, but I don't know if all details are correct. Also, I don't know if the given coil diameter is for...
View ArticleNew team members
Thanks !This looks like a very cost-effective solution !Did you just plug a single antenna out of the iC880A or did you use a powered RRH to increase signal power ?I see that the iC880A advertise a...
View ArticleClik here to view.
How to build your first TTN node: Arduino + RN2483
This is my node running TXfastViaTTN.ino on a Arduino Pro mini and a Microchip RN2483, powered by a 9V battery. Thanks for sharing!
View ArticleToronto & GTA
Hey Almarion, I am interested. 30+ years experience in RF (military, AM/FM radio stations, HAM). I have a large building contractor who is interested in helping/sponsoring us.
View ArticleClik here to view.
How to build your first TTN node: Arduino + RN2483
Nice Marco, I ordered the holiday cards !
View ArticleClik here to view.
Single Channel Gateway
How does the range of such SX1276-based gateway compare to "true" gateways? (Lacking any TTN in my area, I'm trying to figure out if the bad range I get is caused by my node or my single channel...
View ArticleClik here to view.
Single Channel Gateway
Just got a single chan gateway up and running (801F02FFFF7E56D1) with one node (02E00201) sending "Hello, world!" for a few test packets then turned off. Node is a mega2650 w/ a Modtronix inair9b and...
View ArticleClik here to view.
Single Channel Gateway
cswiger: had to change 'eth0' to 'wlan0' in main.cpp Hmmm, I did not change that, and uploading to TTN just works fine on WLAN. But I did have an ethernet cable connected at some point in time; maybe...
View ArticleClik here to view.
Single Channel Gateway
arjanvanb: How does the range of such SX1276-based gateway compare to "true" gateways? Hi Arjen, This depends very much on where the gateway (-antenna) and node are located. Although line of sIght...
View ArticleClik here to view.
Clik here to view.
Clik here to view.
CE certification
Yesway you are right, all equipment operating on less then 50VDC or 75VAC are exempt from testing according EN60950 (safety). However the R&TTE directive clearly states that as soon as there is...
View Article