Looking for gateway owner in Apeldoorn
On the 21th april there will be a open Lora meeting in Apeldoorn.It is on the Zwitsal Vlijtseweg 144 in the Future Lab in building 64, ApeldoornJoin:...
View ArticleAthens, Greece
I'm pleased to announce that for more than a month now TTN is active in Athens center, via a low cost, DIY, outdoor, powered over the ethernet, LoRaWAN gateway. More details on our blog...
View ArticleLoRa FeatherWing Development Breakout
Width is a potential problem on that module. It will nearly touch the header pins, but it should still fit. For the RN2903 I can use a single SMA connector on one end just like the RFM boards. For the...
View ArticleClik here to view.
LoRa FeatherWing Development Breakout
one ufl or one SMA on the 868 Mhz output is ok for the EU you don't need all the feather GPIO pins if you just want to trigger an alarm or measure a tempminimal connections would be Rx Tx 3v Gnd to...
View ArticleRx2 Frequency for USA
Hi All, We are an NYC-area makerspace attempting to setup a TTN gateway (Multitech). We have a few LoRaMOTEs (RN2903) that we are trying to get talking to the gateway. However, we do not see any...
View ArticleClik here to view.
LoRa FeatherWing Development Breakout
This is what an RN2903/RN2483 FeatherWing would like like. In the render it looks like the pins on the module touch the headers. They don't, but they are very close. I would have to make sure this can...
View ArticleClik here to view.
Rx2 Frequency for USA
Chris, You are right, that setting applies to EU868 only. You can just leave it out. It should not affect the reception of your messages by the gateway. Your MultiTech gateways support 8+1 LoRa...
View ArticleLooking for gateway owner in Apeldoorn
vi lorank8v1/local_conf.jsonwill do the trick(first ssh to the gateway with the username/password in the manual)
View ArticleClik here to view.
Clik here to view.
LoRa FeatherWing Development Breakout
Here is what a dual band version looks like for the RN2483. In about 2 weeks I'll have the boards back and know if this super narrow footprint for the RN modules is going to work....
View ArticleClik here to view.
LoRa FeatherWing Development Breakout
Thanks for your work and also for sharing with the community!I'll order a few boards for the RN2903 if your design works.
View ArticleClik here to view.
LoRa FeatherWing Development Breakout
I see you are routing tracks on the top copper layer underneath the RN2483. I always try to avoid this because the RN's datasheet says: "Note: Host PCB top layer copper traces must have solder mask to...
View ArticleLocation by triangulation
Chronos - Decimeter-Level Localization with a Single WiFi Access Point: The key enabler underlying Chronos is a novel algorithm that can compute sub-nanosecond time-of-flight using commodity WiFi...
View ArticleClik here to view.
Anyone used the iM880B-L?
Thank you! I am definitely blind I was in that download section a couple of times, and every time I failed to notice there was a entire section of more documents below the "General Information" one....
View ArticleClik here to view.
mDot Tester GUI
Hi All,I did a GUI in windows to configure and test the Multitech mDot device. You just need to connect the mDot to a PC thru a usb<->rs232 converter and use the GUI. Feel free to...
View ArticleLoRa FeatherWing Development Breakout
Yup, the vias are tented and OSHPark fabs do a good job with solder mask. Dan
View ArticleClik here to view.
mDot Tester GUI
cool ! ( missing one button next to 'close for clearing the txt area' )
View ArticleNijmegen and its surroundings
He fred, ik heb nu deze gateway;http://www.link-labs.com/product/lora-enabled-m2m-gateways/Ben er nog niet uit hoe ik hem aangesloten krijg... Heb je tips? Of ken je mensen die dit wel weten?
View ArticleConnecting linklabs lorawan gateway to ttn
Hi all, I need some help connecting a new gateway... Its the Model: LL-BST-8 Is there someone who can help me? http://www.link-labs.com/product/lora-enabled-m2m-gateways/
View Article